#Remington model 490 parts cracked#
#Remington model 490 parts manual#

Р В РІР‚в„ўР вЂ™Р’В® Remington Power Fasteners are manufactured from special steel and heat treated to produce a very hard yet ductile fastener. NEVER use common nails or other materials as fasteners. Appropriate safety precautions must be taken. An act of demolition is required for their removal. Power fasteners are a permanently installed fixture. Always start with the lowest power level (gray-level 1) and increase until a proper fasten. Remington Powder Loads are available in four power levels with gray (1) being the lowest power level and yellow (4) being the highest power level. L E K C I N R E B Safety Precautions Start 22 1 2 6 7 GRAY BROWN 5 8 4 9 1 3 10 2 11 12 1 3 4 GREEN YELLOW 482-31 482-53 NOTE: Failure to start with the lowest power level can result in overdrive condition and will re- sult in damage to tool (see page 13). If the tool still fails to fire, hold the tool firmly against the work surface for another 30 seconds before unloading and carefully dis- carding the misfired powder load into water or Again press the tool firmly against the work surface and pull the trigger. Release the trigger and remove pressure on the tool while holding the muzzle against the work surface. Should the tool fail to fire, hold the muzzle firmly against the work surface for 30 seconds. DO NOT drive power fasteners into steel base material less then 3/16' thick, within 2' of a weld, within 1/2' of the edge, or within 1' of another power fastener. DO NOT drive power fasteners into concrete less than three times as thick as the intended fastener penetration, within 3' of the edge, within 3' of another power fastener, or within 3' of a failed power fastener. NEVER drive power fasteners into thin or easily pen- etrated material unless it is backed by concrete or steel.

#Remington model 490 parts cracked#

NEVER make fastenings in spalled or cracked areas. Materials of this type tend to shatter and create hazard from flying particles. NEVER attempt to drive power fasteners into very hard or brittle materials including, but not limited to cast iron, glass, tile, stone, brick, or hardened steel. Safety Precautions TILE BRICK CAST IRON GLASS G 018 G 018 482-33 482-32 2. KNOW YOUR FASTENING BASE MATERIAL ? CENTER PUNCH TEST 482-26 482-27 Sinks in Point with flattens average hammer blow TOO SOFT G 018 TOO HARD G 018 482-28 482-29 Start Surface shatters 1 2 GRAY BROWN 3 4 GREEN YELLOW TOO BRITTLE 482-30 NEVER drink alcoholic bever- ages or take medications which impair your vision, balance or judgement before using a powder actuated tool.

An operator taking medication should take extra precau- tions while handling the tool. If the tool is dropped, inspect for damage and repair it before continuing to work. NEVER point a powder actuated tool at anyone. NEVER carry or pass a loaded powder actuated tool. Keep powder loads of different power levels in separate containers. ALWAYS store UNLOADED powder actuated tool and powder loads in a locked container. POWD POWDER LOAD LOADS Safety Precautions G 018 489-16 489-15 3. NEVER place your finger on the trigger until the muzzle of the tool is against the work surface. Accidental discharge can cause serious injury. ALWAYS make sure the work area is clean from loose material and debris. ALWAYS clear the work area on all sides and post appropriate warning signs on job sites. Safety Precautions WARNING POWDER ACTUATED TOOLS ! IN USE 482-10 489-09 4. WARNING: This tool is designed only for use by qualified WARNING ICON G 001 operators. We expressly disclaim any liability for any injury to persons or damage to property which result from your failure to take the precautions contained in this manual. Read carefully and become familiar before operating to avoid serious injury. 17, 18Р В РІР‚СњР вЂ™Р’ВEFECTIVE Warning: Safety WARNING ICON G 001 Precautions The following pages contain detailed warnings, cau- tions, and rules of safe operation.

#Remington model 490 parts manual#

G 028 G 029 Operating Instructions Important: Read this manual and all labels carefully before operat- ing your powder actuated tool. Р В РІР‚в„ўР вЂ™Р’В® REMINGTON Powerdriver Models 489 and 490 490-01 Р В Р вЂ Р Р†Р вЂљРЎвЂєР РЋРЎвЂє Р В РІР‚в„ўР вЂ™Р’В® POWDER ACTUATED TOOL MANUFACTURERSР В РІР‚в„ўР СћРІР‚В INSTITUTE INC.